2002 Elantra Front Disc Removal?

Hyundai Forum Hyundai Classifieds Photo Gallery Member List Calendars Search Contact HF Sponsors
Hyundai Lineup Hyundai News Hyundai Recalls TSBs Timeslips Register Login

2002 Elantra Front Disc Removal?

Printable Version

Hyundai Forum >> Vehicle Line Up >> Hyundai Elantra >> 2002 Elantra Front Disc Removal?

Page: [1]

Message

<< Older Topic Newer Topic >>

2002 Elantra Front Disc Removal? - 9/9/2007 8:03:32 AM

69RocketJoe

Posts: 2
Joined: 9/9/2007
Status: offline

My mom has a 2002 Elantra and we went to do a front brake job. Discs need replacing as she tore the heck out of them. For the life of me I cannot get the old ones off. I removed the little useless screws and beat on the disc with a mallet, no wiggle. Beat on it some more, no wiggle. Got out a 2 jaw puller and put as much torque on it as I could and the discs would not budge. Is there something I am missing here? removed the caliper and hung it up out of the way, pulled the pads out, and removed the two little crappy screws. Any help would be appreciated.

Thanks,

-Joe

Post #: 1

RE: 2002 Elantra Front Disc Removal? - 9/9/2007 6:04:58 PM

NovaResource

Posts: 404
Joined: 5/29/2005
Status: offline

Seriously, use a bigger hammer. I had the beat my rotors off with much more force than I thought I would need to. Huyndai must not know what anti-seize is becaue mine (2004 Tiburon) were rusted on. Use plenty of penetrating oil and hammer them while under the car from the inside out. Also, make sure the set screws are either removed or drilled out.

_____________________________

Octane Truth: Regular or Premium? (Car and Driver Magazine: November 2001)

(in reply to 69RocketJoe)

Post #: 2

RE: 2002 Elantra Front Disc Removal? - 9/10/2007 9:18:58 AM

Doohickie

Posts: 839
Joined: 2/6/2006
Status: online

Unfortunately, the rotors can fuse to the hubs. The best way to get them off once that happens is to cut them off with either a hack saw or a Sawzall. Cut toward the center of the rotor from opposite sides. When you get to the humb, use a chisel to wedge the halves apart and off the hub.

No, I am not kidding.

_____________________________

(in reply to NovaResource)

Post #: 3

RE: 2002 Elantra Front Disc Removal? - 9/10/2007 12:13:58 PM

NovaResource

Posts: 404
Joined: 5/29/2005
Status: offline

^^^ No, he's not kidding. If you have a sawzall than that is a good option. Just remember, however you get them off, be sure to clean the rust from the hubs and use plenty of anti-seize on the new parts.

_____________________________

Octane Truth: Regular or Premium? (Car and Driver Magazine: November 2001)

(in reply to Doohickie)

Post #: 4

RE: 2002 Elantra Front Disc Removal? - 9/10/2007 6:25:06 PM

69RocketJoe

Posts: 2
Joined: 9/9/2007
Status: offline

OK Thanks for the replies. I am guessing it will have to be the sawzall route. Like I said I had the puller on there and they did not even budge. It will be a couple of weeks before I get down there again. I didn't want to go any further without seeing if they were press fit on as the replacement rotors have a bevel on the inside that looked like it could be for guiding a press fit part onto the hub. What about heating them up good with a torch and beating on them? Or is there ABS/ electric crap there I could damage? I don't work a whole lot on newer stuff and rarely on FWD stuff. Thought they would just fall off without the caliper on like the 4x4 trucks I have worked on.

-Joe

(in reply to 69RocketJoe)

Post #: 5

RE: 2002 Elantra Front Disc Removal? - 9/11/2007 8:01:08 AM

Doohickie

Posts: 839
Joined: 2/6/2006
Status: online

When you put the new rotor on, coat the mounting surfaces (both to the hub and to the wheel) with grease; I usually use molybdenum grease. I used to work on tanks and they coated all fasteners and stuff with moly grease to prevent them from seizing up.

_____________________________

(in reply to 69RocketJoe)

Post #: 6

RE: 2002 Elantra Front Disc Removal? - 4/8/2008 5:45:46 PM

Zuul24

Posts: 2
Joined: 4/8/2008
Status: offline

I just went through the same thing. Those 'crappy little screws' are just there to protect the holes that you use to push the rotor off the hub with bolts.

I beat the crap out of my rotors until I realized what those holes were for.

You just take hardened bolts and screw them into the holes and it pushes the rotor right off. I had them done in 10 minutes once I realized what I was doing wrong.

Chas

(in reply to Doohickie)

Post #: 7

RE: 2002 Elantra Front Disc Removal? - 5/8/2008 3:26:58 PM

steppenw7

Posts: 9
Joined: 7/2/2006
Status: offline

Hey, this is great Zuul24, for I just posted a question on this subject yesterday. I suspected that those 2 holes were there to help push the disk away from the hub and even tried it, but I supposed I wasn't using hardened metal bolts because they were bending on me. I will try and source harder metal bolts. Hammering the disk out worries me for I wouldn't want to damage the bearings.

For that matter, I needed to replace 2 studs on one of the front hub. To protect the bearing as I was hammering the worned out studs out of place, I used a clamp to tighten the brake pads on the disk so the bearing wouldn't feel the impact.

Certainly no brownies for the Hyundai engineers for not protecting tyhe disk and hub against fusing together.

GP

(in reply to Zuul24)

Post #: 8